Ardex K 301 further information
Coverage: Approximately 7.8m2 at 2mm thick per 25kg bag
ARDEX K 301 is a Fast Setting Resurfacing and Levelling Compound for Concrete. It is a grey powder consisting of special cements, graded aggregates and high quality synthetic resins. When mixed with water, a fluid mortar is produced which sets after approximately 1 hour and can normally be walked on after 2-3 hours at 20°C. It can be applied from 2mm to 20mm in a single application. The set and hardened ARDEX K 301 is usually ready to receive light rubber wheeled traffic after 48 hours at 20°C.
Adrex K 301 Technical Data
Application depth | 2-20mm |
Working time | 30 minutes |
Walk on time | After 2-3 hours |
Light traffic from | 48 hours |
Coverage | 3m² at 5mm per bag 7.8m² at 2mm per bag |
Bulk density of powder | approx. 1.37kg/litre |
Weight of fresh mortar | approx. 1.94kg/litre |
Initial Set (Vicat) | approx. 40 minutes |
Final Set (Vicat) | approx. 2 hours |
Compressive Strength | After 7 days 20.0 N/mm² After 28 days 28.0 N/mm² |
Tensile Bending Strength | After 28 days 6.5 N/mm² |
Overcoat time for industrial coatings | Up to 5mm = 2 days Up to 10mm = 5 days Up to 20mm = 7 days |
USE
ARDEX K 301 will smooth and level concrete surfaces such as balconies, patios, domestic driveways, garages, walkways and other concrete surfaces exposed to normal foot and rubber wheeled traffic. It can also be used for filling holes and resurfacing damaged floors, such as concrete or a bonded cement/sand screed (>30N/mm2compressive and 1.5N/mm2 pull off), as well as pre-smoothing concrete floors prior to the application of a suitable damp proof membrane, such as ARDEX DPM 1C / ARDEX DPM 1 CR.
NOTE: ARDEX K 301 is not recommended for heavy duty industrial floors, public highways or traffic with solid or metal wheels.
ARDEX K 301 is suitable for permanently wet areas and may be used in swimming pools where it can be tiled onto directly.
ARDEX K 301 is not recommended for areas of intensive abrasive use in wet areas.
Do not apply ARDEX K 301 over asphalt or tarmacadam surfaces.
The hardened ARDEX K 301 should be protected from spillages and materials which damage concrete surfaces. If required, the dried ARDEX K 301 can receive suitablesealers, paints or coatings such as ARDEX WPM 200.
SURFACE PREPARATION/PRIMING
All concrete surfaces should be mature i.e. at least 6 weeks old. The concrete surface must be hard, sound, thoroughly cleaned, free of all oil, grease, curing compounds and other barriers to adhesion. The substrate can be dry or damp. ARDEX K 301 may be unsuitable for aged or frost damaged concrete subject to regular deflection from thermal cycling or mechanical loading.
Use a suitable degreaser to remove oil, grease or similar contaminants and rinse well prior to mechanical preparation. All surfaces must be prepared as necessary to ensure good adhesion. The prepared surface must have the appearance of clean sound concrete with the exposed aggregate in the surface. There must be no traces of any dirt, previous treatments or surface contamination. Concrete surfaces must be mechanically prepared, either by scabbling, grinding or contained shotblasting equipment or similar, and be vacuumed clean prior to priming.
Sufficient and thorough mechanical preparation is essential for commercial areas, especially those intended for exposure to regular or intensive rubber wheeled traffic, or heavy loading. Vacuum the prepared surface to remove all dust and debris, and ideally wash the surface using high pressure water jet equipment.
All cracks in new and old concrete can be repaired to inhibit cracking in the ARDEX K 301 with ARDEX P 10 SR, (refer to the ARDEX P 10 SR datasheet). Any structural, movement or live joints must be carried through the ARDEX K 301 to the surface.
For internal dry applications prime the surface with ARDEX P 51 Primer diluted 1:1 on absorbent or 1:0.5 on non-absorbent substrates. Dilute with clean water, and apply with a brush or broom. Any ponding, puddles or surface water must be removed with a broom so that excess primer is not incorporated in the mortar during application. Let the primer dry before ARDEX K 301 is applied
For external applications prime with ARDEX P 51 Primer diluted 1:7 with clean water, and applied with a brush or broom. Ponding, puddles or surface primer must be removed with a broom so that excess water is not incorporated in the mortar during application. Apply the ARDEX K 301 whilst the priming layer is still damp.
In all areas subjected to regular rubber wheeled traffic or heavy loading, and on dense surfaces, ARDEX R 3 E Solvent Free Epoxy Primer should be used to prime, sand blinding the surface with ARDEX Fine Aggregate while still wet. The surface must be allowed to cure and excess sand removed before applying ARDEX K 301.
MIXING
In a clean mixing container add the powder to the required amount of clean water whilst stirring thoroughly until a lump free mortar is produced. The mix proportions by volume are approximately 5 parts ARDEX K 301 powder to 1 part clean water.
A 25kg bag requires 51⁄4 litres of water.
To pump the mortar, use continuous pumps with a capacity of 20 – 40 litres of mortar per minute.
Do not use excess water as this will reduce the strength of the set and hardened mortar.
The use of an ARDEX mixing paddle with a 10mm chuck slow speed (600 – 1000 r.p.m.) electric drill makes light work of mixing.
ARDEX K 301 mortar should be applied within 30 minutes at 20°C. This time is extended at lower temperatures and reduced at higher temperatures.
APPLICATION
Pour the mixed ARDEX K 301 onto the prepared and primed substrate. The mixed mortar will flow out and self-smooth during the first 10 minutes of its 30 minute working time. Spread the mortar using a steel trowel or float.
For larger areas its recommended to use a gauging tool or ARDEX Pin Leveller with thickness height adjustment to spread the mortar.
The applied ARDEX K 301 surface can be left with a trowelled finish. If gradient levelling has to be carried out, or a broomed finish required, the water content must be reduced.Alternatively, to create a more non-slip finish, the water content should be reduced and then ‘broom finished’ once the initial set has occurred (approximately 40 min-utes under normal conditions).
Once set, the freshly applied ARDEX K 301 must be protected from adverse climatic conditions e.g. rapid drying air flow, direct strong sunlight, frost, etc., or appropriate curing measures must be taken until hardened.
Apply at temperatures above 5°C.
If a second layer of ARDEX K 301 is required, this should be applied after the first layer has fully hardened. The first layer should be machine sanded (paper 16 to 36), cleaned and primed with ARDEX P 51 Primer diluted 1:1 with water for dry indoor use, and diluted 1:7 with water for external use or damp interior areas.
The dilution rate of 1:7 should not be exceeded for external applications
THICKNESS
ARDEX K 301 can be applied neat from 2mm to 20mm thick.
NOTE: The thickness of combined layers should not exceed 20mm.
STORAGE AND SHELF LIFE
ARDEX K 301 must be stored in unopened packaging, clear of the ground in cool dry conditions and protected from excessive draught. If stored correctly, the shelf life is 12 months from the date of the packaging.
There are no reviews yet.