Everbuild PinkGrip Professional Grab Adhesive – Bulk Buy

Everbuild PinkGrip extended information

Consumption: Approx. 12 linear meters for a 6 mm bead.

Characteristics & Advantages

• Enhanced slump resistance for quick and simple direct bonding to most substrates without the use of temporary supports in most applications.
• Pink colour gives easy product recognition.
• Excellent early and ultimate adhesive strength on both porous and non-porous substrates.
• Excellent gap-filling properties to accommodate uneven surfaces.
• Good “nip off” qualities to prevent messy stringing of the adhesive.
• No need for double-stick applications or underpinning in many instances (although product may be used via double stick method if required).
• Suitable for both vertical and horizontal use.
• Suitable for use on both non-porous and porous surfaces.
• Excellent external weathering properties.
• Suitable for interior and exterior use.

Everbuild PinkGrip product information

Packaging	Cardboard cartridge
Shelf Life	12 months from date of manufacture in unopened containers.
Storage Conditions	Store in original unopened containers between +5 °C and +25 °C. Do not store above +30 °C. Store as flammable goods.
Colour	Pink
Density	1.2 – 1.3 g/cm3
Consistency	Pink Paste

Everbuild PinkGrip technical information

Thermal Resistance	-20 °C to +50 °C
Chemical Resistance	Excellent to dilute acids and alkali, poor to most organic solvents.

Everbuild Pinkgrip test results

TEST	Result
Viscosity	~400,000 mPas
Solids Content	70 +/- 1 %
Ash Rate	45 +/- 1 %
VOC	30 +/- 1 %
Flash Point	-10 °C

LIMITATIONS

• Do not use on damp surfaces: use EVERBUILD GUN A NAIL.
• Do not use as a mirror adhesive: use EVERBUILD STIXALL.
• Do not use on polystyrene/Styrofoam/expanded polyurethane – use EVERBUILD GUN A NAIL.
• Heavy materials (greater than 10 kg per sq metre) must be supported for at least 8-24 hours depending on size of item.
• Solvents present may attack sensitive plastics. If in doubt, test a small area first.
• Only suitable for overhead applications when used in conjunction with mechanical fixings.

SUBSTRATE PREPARATION

The surfaces to be glued must be clean, dry and free from dust, grease and other contaminants. New concrete or plaster should be allowed adequate time to dry and mature. If this is not possible, use EVERBUILD GUN A NAIL.

Porous or friable surface should first be primed with dilute contact adhesive or PVA and allowed to dry.

APPLICATION METHOD / TOOLS

• All surfaces to be sealed must be sound, clean, dry and totally dust free.
• Cut the tip of the cartridge taking care not to damage the thread.
• Cut nozzle cleanly at an angle of 45 degree and pierce membrane. Apply using a standard sealant gun.

DIRECT BOND METHOD

Apply a 6 mm bead in a zigzag along the length of the item to be fixed. For panels, centre beads at 350 mm max. Press into place and apply an even pressure onto the entire surface. Leave to cure for 24-48 hours. For extremely heavy i

Packaging	Cardboard cartridge
Shelf Life	12 months from date of manufacture in unopened containers.
Storage Conditions	Store in original unopened containers between +5 °C and +25 °C. Do not store above +30 °C. Store as flammable goods.
Colour	Pink
Density	1.2 – 1.3 g/cm3
Consistency	Pink Paste

tems, provide temporary support whilst curing. Where gap filling is necessary, for example battens against an uneven wall, mark the areas where there is a larger gap and apply a thicker bead in these areas.

DOUBLE-STICK METHOD

Apply adhesive as above. Immediately press firmly into position to ensure adequate transfer of the adhesive and then pull away to affect the adhesive transfer. Allow adhesive to dry apart for 5 minutes before pressing finally into position. Allow to dry for 24 hours before subjecting to traffic.

Everbuild Pinkgrip CLEANING OF TOOLS

Tools and excess adhesive can be cleaned using white spirit or turpentine substitute.