!FREE DELIVERY on Every Order (Most of Mainland UK) *
,

Larsen DPM One Coat Rapid – Bulk Buy

Larsen

Larsen DPM One Coat Rapid

It’s a superior 2 pack epoxy surface applied damp proof membrane ideal for Fast-Track applications. Allows immediate installation of moisture sensitive floor finishes onto damp concrete and screed. It is designed for use as a one coat application depending on the moisture content of the floor and allows same day covering.

  • SINGLE COAT APPLICATION
  • WALKABLE IN 4 HOURS
  • FAST TRACK APPLICATIONS
  • UP TO 98%RH IN ONE COAT

You can add this product to your order, however there must be a pallet/half/three-quarter-pallet in the cart to checkout.

Need a custom deal? 0333 344 2655 or info@buythepallet.co.uk

£134.00 +VAT

£134.00 +VAT
x

Larsen DPM One Coat Rapid extended information

Coverage:

Floor RH%No. of CoatsMinimum Film ThicknessMinimum ApplicationMaximum Coverage
Up to 85%1250μm400g / m225m2/10kg
Up to 98%*1350μm555g / m218m2/10kg

* or where structural DPM is absent, alternatively use Larsen Universal DPM in 2 coats

Larsen DPM One Coat Rapid product information

FORM2 part solvent free epoxy coating
COLOUR(S)Black
HAZARD INFORMATION:Part A – WARNING Irritant, Toxic to aquatic life
Part B – DANGER Harmful, Causes Severe burns, May cause an allergic reaction,Toxic to aquatic life
Consult MSDS for full information before use.
Note: After mixing and curing the material is non-hazardous.
CLEANING:Clean tools, equipment etc. using suitable solvent thinners. Mechanical means are necessary when the product has set.
PACKAGING:10kg packs
STORAGE CONDITIONS:Store in sealed containers in dry conditions, protected from extremes of temperature
SHELF LIFE:Typically 24 months in good storage conditions

Larsen DPM One Coat Rapid application information

MIX RATIO:Part A 8.3kg
Part B 1.7kg
(It is not recommended to split packs without the use of accurate weighing equipment.)
POT LIFE:Approx. 20-30min @ 20oC
APPLICATION TEMPERATURE:+5oC to +30oC
DRYING TIME:Touch dry 1-2 hrs Walkable - 4 hrs @20oC
UNDERFLOOR HEATING:Suitable for use with heated concrete and cement screeds up to a maximum surface temperature of 27°C.
MOISTURE VAPOUR PERMEABILITY<5g / m2 / 24hours

DIRECTIONS FOR USE

PREPARATION

The substrate should be hard, structurally sound and stable concrete or cement based screed of sufficient strength for the floor use. The surface should be surface dry and free from laitance, dust or other contamination which may affect adhesion. It is recommended to mechanically prepare the surface by enclosed shot blasting or diamond grinding then vacuum thoroughly.

It is recommended to carry out a thorough survey of the floor with moisture testing carried out as per BS8203 with suitable, calibrated hygrometers. These figures should then be used to determine the recommended maximum coverage and minimum film thickness of Larsen DPM. It is recommended to record and keep the results of the moisture testing. Electric resistance moisture meters are only indicative and should not be used to determine minimum film thickness of DPM.

Construction joints in the floor must not be bridged by DPM. ‘Live’ cracks in the floor must not be bridged by DPM. Existing static cracks must be fully repaired by stitching or resin injection as required before the DPM is applied.

When applying over heated screeds, ensure the screed is cement based and that the heating system has been fully commissioned, including raising to maximum running temperature. The heating system should be switched off a minimum of 48hours before applying Larsen DPM and the temperature raised gradually starting a minimum of 48hrs after installing floor finishes in such a way as to avoid thermal shock or rapid temperature variations. The screed should not have a surface temperature above 27°C.

MIXING

Before use it is recommended to condition all packs at a temperature of 15-25°C for 24 hours.

Pour hardener (Part B) into base resin (Part A). Mix thoroughly with a slow speed drill and paddle. It is recommended to employ a back mixing method by emptying the mixed parts into another container and mixing again.

Mixing by hand is not suitable.

APPLICATION

Mark out the area to ensure the correct coverage depending on the required minimum film thickness. During application check the minimum wet film thickness (disposable wet film gauges are readily available and inexpensive). After application double check the number of packs used was correct.

ONE COAT APPLICATION – (Only suitable with floor moisture up to 98% RH)

Do not exceed maximum coverage of 25m2/10kg pack at up to 85%RH or 18m2/10kg pack up to 98%RH.
After fully mixing pour out the DPM on the floor and spread to an even thickness for example with a suitable V-notched trowel. Typically a 1.5 x5mm fine notch trowel is suitable to achieve a coverage of approx.. 400g/m2 and an A2 trowel achieves a coverage of approx. 555g/m2. The wet DPM must then be leveled by rolling with a suitable roller, pre-wetted in DPM. It is important to ensure the coating is continuous, is of the minimum required film thickness and is free from pinholing. Should this not be the case, a second coat should be applied.

SUBSEQUENT LAYERS

Depending on the subsequent layers in floor, different systems may be employed as follows:
DIRECT APPLICATION OF FLOORING ADHESIVE – check with adhesive supplier that this method is suitable and compatible with the DPM.
LEVELLING COMPOUNDS – When overlaying with latex levelling compounds (e.g. Lartex FLO or Lartex NA) the same day, no primer is required. Overlaying after 12 hours or with water based levelling compounds, prime first with Larsen NP Keycoat or NP Grip 360 . When subsequent layers are thicker than 6mm or in heavier traffic applications, prime with Larprime EU and sand scatter – consult technical dept. for full details.

RESTRICTIONS

All work should be carried to current best practice, including British Standards (including BS8203 and BS8204) and CFA and FeRFA Guidance documents. DPM One Coat Rapid is not suitable for resisting hydrostatic pressure, nor will it necessarily reduce the incidence of osmotic blistering. Larsen DPM One Coat Rapid should not be used on substrates which are not moisture tolerant and should not be used on gypsum or magnesite screeds. Curing times are affected by site and substrate temperatures and it is recommended that both are above 10°C. Insufficient mixing, incorrect mixing ratio and temperatures below 5°C will result in lack of uniform hardening and failure of the integrity of the DPM.

Brands

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Larsen DPM One Coat Rapid – Bulk Buy”

There are no reviews yet.

 

Buy The Pallet - Tile Adhesive and Floor Levellers Discount Store

5.0Out of 5 stars

Overall rating out of 20 Google reviews

Dean Clare
12 hours ago

Top quality service.

Kelvin Wiltshire
12 hours ago

We have been using BuyThePallet for our levelling products for over two years now. Their customer support and attentiveness to our needs makes ordering and receiving goods a pleasant and easy step towards our next project. The prices are extremely competitive, delivery drivers are polite and accommodating and overall a brilliantly run business. If you want hassle a free company then these are the guys to buy from. NMA Flooring Ltd, Devon/Cornwall

Aaron Nairn
4 months ago

Fantastic customer service and fast delivery, highly recommend

Gary Dawson
8 months ago

Great prices and a super quick delivery turnaround. Communication was perfect aswell. So much so I’ve ordered again.

Phil Down
9 months ago

They actually answered the phone, were polite, knowledgeable and the order was delivered in full and on time. Would fully recommend both on price and service. Thank you.

Dom
10 months ago

BTP very helpful in supplying a pallet of floor leveller. I needed it on the Saturday, but didn’t want it sitting on the driveway for several days. I called and they recommended ordering for Thursday to give a day’s grace in case of any delivery issues. In the event the pallet arrived on Thursday as requested. Reliable and good value

Gary Harper
11 months ago

Great service, great price and great communications. We will definitely use Buy The Pallet again

Adrian W
a year ago

Great service and delivery! Ordered all that I needed in one go and it was delivered to the back door wrapped and protected from the snow! Pallet even made it so that the goods were dry off the ground.

Rob Jones
3 years ago

Companies like this a rare, great quick service, great price and easy to do business with. Will definitely use them again for all my supplies.

Boon Teo
a year ago

Great prices with a good ranges of products . Customer Service is excellent!

Peter Bostock
3 years ago

I purchased a pallet of these and I am very impressed from ordering to receiving my pallet and the delivery guys were very helpful as well .I will definitely recommend and use this company again .Highly recommend

Kev in
3 years ago

Amazing knowledge and great prices! Definitely using these guys on a regular basis for my pallet deals on levellers and adhesive

Richard Fairlie
3 years ago

Great service and really good pricing! Super fast delivery and really lovely guy!

Rob Faulkner
3 years ago

Fantastic experience with Buy The Pallet. Everything I needed to complete a large flooring project, quick delivery & quality products.

phil harvey
4 years ago

First class service, good price, fast delivery and the chap at the end of the phone knew what he was on about. Highly recommend and will use them again.

Max Simpson
a year ago

Very helpful!

Marc. T
3 years ago

Very helpful

Kelvin Wiltshire
12 hours ago

We have been using BuyThePallet for our levelling products for over two years now. Their customer support and attentiveness to our needs makes ordering and receiving goods a pleasant and easy step towards our next project. The prices are extremely competitive, delivery drivers are polite and accommodating and overall a brilliantly run business. If you want hassle a free company then these are the guys to buy from. NMA Flooring Ltd, Devon/Cornwall