!FREE DELIVERY on Every Order (Most of Mainland UK) *
, , ,

Larsen Pro Flexible Rapid Set Tile Adhesive S1 White / Grey 20Kg – Pallet Deals and Bulk Buy

Larsen

Larsen Pro Flexible Rapid Set Tile Adhesive S1

Professional Flexible Rapid Set+ is a specially formulated, fully flexible, S1 rated, fast setting, cement based tile adhesive.

It is suitable for beds of 3 – 20mm, interior, exterior, floor and wall applications. Larsen Pro Flexible Rapid Set+ is suitable is suitable for fixing most tile types and is recommended for fully vitrified tiles, natural stone glass mosaics and large format tiles. It is recommended for use on more demanding substrates including heated screeds, overboarded timber and swimming pools.

  • Suitable for: ceramic, marble/natural stone, porcelain, glass, mosaic tiles
  • Suitable for: under floor heating and over sheeted timber
  • Deformable
  • Grout after 3 hours
  • BS EN 12004 Type C2FS1
  • Available in Grey or white
  • 20Kg bags

Spotted a pallet deal cheaper than ours? We can usually beat it! 0333 344 2655 or info@buythepallet.co.uk

~ FREE DELIVERY on Larsen 2 - 4 days ~

£449.90£638.90 +VAT

£449.90 +VAT
£482.90 +VAT
£579.90 +VAT
£638.90 +VAT
x

Larsen Pro Flexible Rapid Set Tile Adhesive S1 extended information

Coverage: 4m2/20kg bag @ 3mm bed

Larsen Pro Flexible Rapid Set Tile Adhesive S1 product information

FORM:Powder
STANDARD COLOUR(S):Grey or White
HAZARD INFORMATION:IRRITANT - Consult Safety Datasheet before use
CLEANING:Clean tools, equipment etc. using warm water.
Mechanical means are necessary when the product has set.
PACKAGING:20kg multiwall, sealed paper sacks
STORAGE CONDITIONS:Store in sealed containers in dry conditions, protected from extremes of temperature
SHELF LIFE:6 months in unopened manufacturer's packaging

Larsen Pro Flexible Rapid Set Tile Adhesive S1 performance information

TENSILE ADHESION STRENGTH:≥1MPa under all test conditions
EARLY TENSILE ADHESION STRENGTH:≥0.5MPa after 6 hours
TRANSVERSE DEFORMATION:≥2.5mm < 5mm
CLASSIFICATION:EN12004 Type C2 F S1

DIRECTIONS FOR USE

PREPARATION

General All substrates must be suitably dry and comply with the recommendations in the British Standards and TTA Guidance documents. All substrates should be clean and thoroughly sound; they should be free from standing water, oils, grease, dust, loose particles or any other contaminants which may interfere with adhesion. Gypsum Based Screeds Gypsum based screeds require mechanical preparation by buffing, vacuuming etc. The screed must be tested to ensure it is dry (less than 0.5% moisture content measured by CM). All gypsum based screeds should be primed as follows: first coat Larsen Acrylic Primer diluted 1:1 with water and allowed to dry; second coat Larsen Acrylic Primer applied neat and allowed to dry fully. If particularly absorbent, subsequent coats may be required.

Gypsum Plaster Gypsum plaster on walls is suitable for a weight of tiles and adhesive of up to 20kg/m2. Plaster should not be dusty or overly polished and should be primed with Larsen Acrylic Primer. Underfloor Heating New heating systems must have been trialled at a high temperature for a period of at least 48 hours in advance of tiling. Ensure the heating is turned off at least 48 hours before any tiling work is carried out and not turned on until at least 7days after the work has been completed. Heating should be turned on at the lowest setting and the temperature increased by no more than 5°C per 24 hours. Particular attention should be given to ensure there is adequate provision for movement joints in the tiling. Timber Substrates Timber substrates must be sufficiently rigid and supported to be free from excessive deflection under expected loads. Ensure adequate ventilation exists beneath the floor. Ensure all new wood (including joists) is ‘dry’ and conditioned. The floor should be designed to accommodate both seasonal changes in moisture and the changes caused by step changes in heating. Extra joists/noggins should be added to strengthen the floor as required. In wet areas timber substrates must be suitably tanked. Plywood on walls is suitable for a weight of tiles and adhesive of up to 32kg/m2. Plywood or Chipboard: Plywood should be at least 18 mm exterior grade and chipboard should be flooring grade. Boards should be free from any wax or other coating which may impair bond. Ensure surface is free from contamination and that the backs and edges of all boards are sealed against moisture ingress.

Screw fix the boards at 300 mm centres and at 150 mm centres along joints. Ensure all edges are fully supported along joists or noggins.

If insufficient support exists to allow this or if excess deflection is evident, extra noggins/joists should be added or consideration given to overboarding. Plywood overlays should be at least 15mm thick. Ensure surface is free from contamination and that the backs and edges of all boards are sealed against moisture ingress. Screw fix the boards at 300 mm centres and at 150 mm centres along joints. Ensure screwed to joists and noggins, not just original boards. Joints between boards should be staggered with original joints. Movement Joints It is important to ensure that there is adequate provision of movement joints in all wall and floor tiling, It is recommended to follow the guidance provided in BS 5385 and by the Tile Association and proprietary joint manufacturers. Ideally, movement joints should be detailed by the designer at the outset. For further information or for situations which are not covered above. consult our website or contact our Technical Dept.

PRIMING

Larsen Acrylic Primer should be used to prime surfaces when required. On porous substrates, dilute 1:1 with clean water and allow to dry before applving adhesive. On impervious substrates, apply primer neat and allow to dry. Tiling should be carried out when the primer has dried clear but remains tacky.

MIXING

The adhesive should be added to clean water (approx. 4.5L water/20kg) adhesive and mixed with a suitable forced action mixer or slow speed drill and paddle until a slump free mortar is produced. The mixed adhesive is usable for up to 45 minutes depending on site temperature and conditions. Do not attempt to remix adhesive or add extra water after it has begun to stiffen as this will cause a loss in performance.

Larsen Pro Flexible Standard Set Tile Adhesive S1 APPLICATION

The mixed adhesive should be applied to dry areas on walls using a suitable notched trowel and applied by solid bed on wet areas on walls, on all exterior tiling and on all floor tiling. In addition, when fitting large format tiles it is highly recommended to also fully skim the back of the tile with a thin layer of adhesive. Tiles should be placed with a firm twisting action before the adhesive has skinned over, i.e. within the open time. Regularly check to ensure adequate contact between adhesive, tile and substrate. ‘Dot and Dab’ method of fixing is not suitable.

GROUTING

Only grout when the tile adhesive has set. Typically this is within 18 hours for standard setting adhesives and within 3 hours for fast setting adhesives.

Larsen Pro Flexible Standard Set Tile Adhesive S1 RESTRICTIONS

‘Dot and Dab’ method of fixing is not suitable. Tiles should not be fixed to wooden substrates externally or in wet areas. Excessive deflection / movement resulting from incorrect preparation will result in cracking of tiles and/or debonding. Floating Timber and Laminate floors are not recommended substrates for direct fixing of rigid floor finishes. Pale coloured marble/porcelain can be translucent and dark coloured adhesive can sometimes show through. If in doubt we would always recommend tiling a small trial area using a white adhesive and back buttering the tiles to ensure a uniform adhesive coverage. Cement-based products will take longer to harden and set at lower temperatures, and should not be used below 5°C. All tiling should be carried to current best practice, including British Standards and TTA Guidance documents.

Brands

Units

20Kg bags

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Larsen Pro Flexible Rapid Set Tile Adhesive S1 White / Grey 20Kg – Pallet Deals and Bulk Buy”

There are no reviews yet.

 

Buy The Pallet - Tile Adhesive and Floor Levellers Discount Store

5.0Out of 5 stars

Overall rating out of 16 Google reviews

Phil Down
3 hours ago

They actually answered the phone, were polite, knowledgeable and the order was delivered in full and on time. Would fully recommend both on price and service. Thank you.

Dom
3 weeks ago

BTP very helpful in supplying a pallet of floor leveller. I needed it on the Saturday, but didn’t want it sitting on the driveway for several days. I called and they recommended ordering for Thursday to give a day’s grace in case of any delivery issues. In the event the pallet arrived on Thursday as requested. Reliable and good value

Gary Harper
2 months ago

Great service, great price and great communications. We will definitely use Buy The Pallet again

Adrian W
4 months ago

Great service and delivery! Ordered all that I needed in one go and it was delivered to the back door wrapped and protected from the snow! Pallet even made it so that the goods were dry off the ground.

Stephen Tucker
4 months ago

Great customer service and at an unbeatable price. All delivered on the day I needed it.

Boon Teo
4 months ago

Great prices with a good ranges of products . Customer Service is excellent!

Max Simpson
5 months ago

Very helpful!

Neil Salih
3 years ago

Peter Bostock
3 years ago

I purchased a pallet of these and I am very impressed from ordering to receiving my pallet and the delivery guys were very helpful as well .I will definitely recommend and use this company again .Highly recommend

Kev in
3 years ago

Amazing knowledge and great prices! Definitely using these guys on a regular basis for my pallet deals on levellers and adhesive

Rob Faulkner
3 years ago

Fantastic experience with Buy The Pallet. Everything I needed to complete a large flooring project, quick delivery & quality products.

Richard Fairlie
3 years ago

Great service and really good pricing! Super fast delivery and really lovely guy!

Marc. T
3 years ago

Very helpful