Everbuild Triple Action Wood Treatment extended information
Consumption: Use as supplied (do not dilute). 1 litre will treat 3-4 square metres.
EVERBUILD Triple Action Wood Treatment takes care of all your wood treatment and preservation needs in one can. It is a low-odour solution based on Micro-fine active technology with added fungicides, algaecides and Permethrin to activelv kill and protect against wood rot, decay, fungi and wood-boring insects. The fungicides and algaecides present in these formulations are finely dispersed so that wood penetration, and hence effectiveness, is much greater than standard wood preservation products.
EVERBUILD Triple Action Wood Treatment is fast drying and non flammable, and application to wet timber is possible without loss of performance. It is specifically designed to deeply penetrate all wood and joinery to give long lasting protection from damage caused by wet rot, dry rot, decay, fungi and wood-boring insects/larvae.
USES
For interior and exterior use on wood such as:
- Sheds and garages
- Fencing and farm buildings
- Roof beams and joists
- Garden furniture.
- Floorboards
- Window frames and doors.
CHARACTERISTICS / ADVANTAGES
- Non flammable.
- Internal and external use.
- Can be applied to damp timbers.
- Penetrates deeply into the wood.
- Long lasting protection.
- Fast drying.
Everbuild Triple Action Wood Treatment product information
Packaging | 1L, 2.5L, 5L and 25L tins |
Shelf Life | Use within 2 vears of manufacture. |
Storage Conditions | Store between 5°C and 25°C in original containers away from children. |
VALUE BASE
All technical data stated in this Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
LIMITATIONS
- Ready to use – do not dilute.
- For use only as specified as a surface biocide and wood preservative.
- Always use coarse rather than fine mist generators.
- Do not apply to surfaces on which food is prepared.
- Avoid contact with bitumen, roofing felt or plastics.
- External timbers must be overcoated to reduce environmental impact.
- Test on a small, inconspicuous area before treating larger areas.
- It is the user’s responsibility to determine suitability for use. If in doubt, contact Technical Services De- partment for advice.
ECOLOGY, HEALTH AND SAFETY
User must read the most recent corresponding Safety Data Sheets (SDS) before using any products. The SDS provides information and advice on the safe handling, storage and disposal of chemical products and contains physical, ecological, toxicological and other safety-related data.
STATUTORY CONDITIONS IN RELATION TO USE:
FOR USE ONLY AS A WOOD PRESERVATIVE AND SURFACE BIOCIDE. 1 LITRE WILL TREAT 3-4 SQUARE METRES WHEN APPLIED BY BRUSH OR SPRAY. IF DIPPING, DIP FOR AT LEAST 3 MINUTES. READ ALL PRECAUTIONS BEFORE USE.
APPLICATION INSTRUCTIONS
Precautionary Notes
ALWAYS READ STATUTORY CONDITIONS RELATING TO USE BEFORE STARTING ANY WORK. Ensure good ventilation before applying and after application until the treatment has dried (HSE statutory 1 hour re-entry time or until surfaces are dry) NOTE: drying times will be extended in cold weather and if ventilation is restricted. Avoid contact with skin and eyes, remove any splashes immediately. Clean up spills immediately (to avoid staining) with warm soapy water.
In roof areas, felt under tiles must be protected from contact with the fluid. Roof insulation must be removed and only replaced when treated timbers are thoroughly dry. Water storage tanks must be covered. When treating flooring and joists, boards should be left up for as long as possible to assist ventilation/drying.
Switch off electrical circuits in the area being treated before, and until 48 hours after, treatment. PVC covered electrical wiring will not normally be affected, but it is recommended that any excess is wiped from cables wherever possible.
SUBSTRATE QUALITY / PRE-TREATMENT
Ensure that surfaces are clean and free from paint var- nish, stain, grease, bark or any other contaminants. Surfaces may be damp. If decay is already present, remove all decayed wood and replace with sound treated timber.
Everbuild Triple Action Wood Treatment APPLICATION
Shake well before use. Apply by brush, spray or dipping. Apply a minimum of two coats if brushing or spraying. The second coat should be applied after the first coat has dried. Pay particular attention to thoroughly soaking the end grain. Where possible, and for maximum protection, dip the end grains of the timber for a minimum of 3 minutes
NOTE: product is milky out of the can but dries clear
There are no reviews yet.