!FREE DELIVERY on Every Order (Most of Mainland UK) *
, ,

ATLAS GEOFLEX Gel Tile Adhesive 25Kg – Pallet Deals & Bulk Buy – Highly Flexible 2-15 MM GREY / WHITE

ATLAS

ATLAS GEOFLEX Gel Adhesive for Tiles, Porcelain and Natural Stone

is a highly flexible gel adhesive (2-15 mm) C2TE

  • suitable for ceramic, porcelain and natural stone
  • for tile on tile, OSB, terrace, balcony, underfloor heating
  • non-slip on a wall or full spread on a floor
  • bed depth up to 15 mm
  • walking and grouting just after 12 hours

Spotted a pallet deal cheaper than ours? We can usually beat it! 0333 344 2655 or info@buythepallet.co.uk

~ FREE DELIVERY on ATLAS pallet deals: 48 Hours ~

£738.00£768.00 +VAT

£738.00 +VAT
£768.00 +VAT
x

ATLAS GEOFLEX Gel Tile Adhesive extended information

Consumption:

Tiles size [cm]Place of applicationRecommended notches size [mm]Consumption [kg/m3]
2x2wall
41.3
floor41.3
10x10wall41.3
floor62.0
15x60wall62.0
floor82.5
20x25wall62.0
floor82.5
25x40wall62.0
floor82.5
30x30wall62.0
floor82.5
30x60wall82.5
floor103.0
40x40wall82.5
floor103.0
50x50wall82.5
floor103.0
tiles – slab type* e.g. 20 x 90 or 15 x 100wall82.5
floor103.0

*for tiles of slab type, it is recommended to use the combined method of tiles fixing.
In case of application of tiles with so called combined method, the consumption is increased. In case of installation of a tiles on the loor with a 12 mm trowel with semicircular notches (liquefied consistency 8.25 l water / 25 kg of dry mix) – consumption 4.6 kg/m2 .

ATLAS GeoFlex technical data

Bulk densityca. 1.4 g/cm3
Mixing (water/dry mix)0.26 – 0.33 l / 1 kg
6.5 - 8.25 l / 25 kg
Min./max. bed depth2 mm / 15 mm
Adhesive preparation temperature, substrate and ambient temperature during workfrom +5°C to +35°C
Maturing time5 minutes
Pot life*approx. 4 hours
Open time*min. 30 minutes
Adjustability time*20 minutes
Walk on/grout*after 12 hours
Full operation load – foot traffic*after 3 days
Full operation load – vehicle traffic*after 14 days
Floor heating (warm surface)*after 14 days

Gel Technology

The unique gel technology used in ATLAS GEOFLEX brings the following advantages:

  • adhesive is suitable for any type of cladding: ceramic,porcelain,naturalstone,
  • consistency of adhesive can be adjusted to individual preferences of the tiler and needs of specific job – mixing ratio is much wider than in case of traditional adhesives,
  • bed depth up to 15 mm – substrate levelling and tiling at once,
  • full spread under the tile with higher mixing ratio – ensured adhesion and durable bond, which is relevant for exterior use,
  • safe cladding installation on surfaces exposed to direct sunlight – during fixing cladding, as well as during mortar setting (e.g. on balcony, terrace).

Properties

ATLAS GEOFLEX is a grey C2TE adhesive for tiles manufactured as a dry mix of high quality cement binder, aggregates and selected modifying agents.

Wide range of bed thickness from 2 up to 15 mm.

No slip from the wall – cladding can be installed from the top of the wall with no additional support.

Walking on and grouting just after 12 hours – owing to accelerated process of adhesive setting and drying.

Use

Cladding Type

glazed tiles+
terracotta+
porcelain tiles+
laminated tilesuse ATLAS ULTRA GEOFLEX
natural stone (granite, marble, travertine, syenite, slate)application test required*
clinker+
stoneware+
ceramic mosaic+
glass mosaicapplication test required*
glass, coloured, printed tilesapplication test required* and check recommendations of tiles manufacturer
concrete/cement mortar tiles+
composite panelsuse ATLAS ULTRA GEOFLEX
insulation and sound absorbing panelsuse ATLAS ULTRA GEOFLEX

*application test description shown on section Important additional information

Size of Installed Elements

small, medium and large format tiles (≤ 0.25 m2) and greater edge length ≤ 100 cm+
extra-large tiles size (> 0.25 m2)use ATLAS ULTRA GEOFLEX
slim type tilesuse ATLAS ULTRA GEOFLEX

Object Type

residential buildings+
public access, educational, office and healthcare facilities+
commercial and service buildings+
sacral buildings+
industrial buildings and multi-storey garagesuse ATLAS ULTRA GEOFLEX
industrial warehousesuse ATLAS ULTRA GEOFLEX
infrastructure buildingsuse ATLAS ULTRA GEOFLEX
SPA objectsuse ATLAS ULTRA GEOFLEX

Installation Area

surfaces with low traffic+
surfaces with moderate traffic+
surfaces with large trafficuse ATLAS ULTRA GEOFLEX
kitchen, bathroom, laundry, garage (in residential buildings)+
terraces+
balcony, loggia+
external slab stairs+
external post stairs (e.g. cantilever stairs)use ATLAS ULTRA GEOFLEX
communication routes+
facades (including external thermal insulation systems)use ATLAS ULTRA GEOFLEX
cladding on a plinths+
technological reservoirs, swimming pools, fountains, jacuzzi, balneotechnology (without aggresive chemical agents)use ATLAS ULTRA GEOFLEX
drinking water reservoirsuse ATLAS PLUS
saunause ATLAS ULTRA GEOFLEX
showers, car washes, rooms washed with plenty of water+

Substrate Type-Standard

cement floors and screeds+
anhydrite screeds+
cement, cement-lime plasters+
gypsum plasters+
cellular concrete+
ceramic brick or hollow blocks+
gypsum blocks+

Substrate Type-Difficult

concrete+
terrazzo+
mineral, dispersive and reactive sealing coats+
plasterboard drywall+
screeds (cement or anhydrite) with water or electrical underfloor heating+
screeds with heating mat embedded in the adhesive+
plasters with wall heating+
plasterboards+
gypsum fibre boards+
cement fibre boards+
existing ceramic or stone cladding (tile on tile)+
resin varnishes on concrete, bonded with substrate+
dispersive, oil painting coats, bonded with substrate+
timber floors (thickness > 25 mm)+
OSB/3, OSB/4 and plywood boards on the floor (thickness > 25 mm)+
OSB/3, OSB/4 and plywood boards on the wall (thickness > 18 mm)+
metal and steel+
plastics+

ATLAS GEOFLEX adhesive is applicable also for floating of standard and difficult substrates mentioned above

ATLAS GEOFLEX Application

Adhesive preparation

Pour the adhesive from the bag into a container with the suitable amount of water (see Technical Data for ratio) and mix, using a low speed mixer with a drill for mortars, until homogenous. The dispersed adhesive should be left to rest for 5 minutes and then remixed. So prepared adhesive should be used up within approx. 4 hours.

Adhesive application

The adhesive should be applied onto the surface with a steel trowel and then distributed evenly and shaped (possibly in one direction) using a notched trowel. It is advisable to rub a thin adhesive coat first and then apply the thicker coat and shape it with a notched trowel. It is recommended to lead a notched trowel in one direction. On walls, it’s recommended to shape the adhesive in vertical direction.

Placing the tiles

After the application, the adhesive retains its properties for ca. 30 minutes (in temperature approx. 23 °C and 55 % humidity). Within this time, the tile must be placed and pressed well (the contact surface between the adhesive and the tile should be uniform and as large as possible – min. 2/3 of tile surface). Remove the excess of the adhesive pressed into the joints immediately.

In case of floor tiles or tiling outdoors it is advisable to keep the full bonding surface (use the mixed method consisting in application of the adhesive on the substrate and tile bottom side, if needed). Keep the joint width appropriate for the tile size and operation conditions (check data in the sheets of ATLAS grouts). Tile adjustment

The position of a tile can be adjusted with delicate moves along the bonding plane. It can be done within approximately 20 minutes since the tile is pressed (in temperature approx. 23 °C and 55 % humidity).

Grouting and cladding use

Foot traffic and grouting with ATLAS grouts can start after approx. 12 hours since the tiles fixing. The mortar reaches the operational strength after 3 days (check the Technical Data). Expansion joints, joints along the wall corners, at sanitary equipment, etc. should be filled with sanitary silicone ATLAS ELASTIC SANITARY SILICONE or ATLAS SANITARY SILICONE SILTON S.

ATLAS GEOFLEX Substrate type and Recommendations

Substrate typeRecommendations
Freshly applied cement screeds ATLAS POSTAR 80, ATLAS SMS 15 or SMS 30Stabilized min. 24 hours; optimum moisture content < 4% by weight.
Freshly applied cement screed ATLAS POSTAR 20Stabilized min. 2 days; optimum moisture content < 4% by weight.
Other cement screedsStabilized min. 28 days; optimum moisture content < 4% by weight. Prime with ATLAS UNI-GRUNT, ATLAS UNI-GRUNT ULTRA or ATLAS UNI-GRUNT PLUS.
Anhydrite screeds ATLAS SAM 100, SAM 200 or SAM 500Stabilized min. 2-3 weeks; optimum moisture content < 0.5% by weight. Prime with ATLAS UNI-GRUNT, ATLAS UNI-GRUNT ULTRA or ATLAS UNI-GRUNT PLUS. If, white surface tarnish forms during screed drying, it should be removed mechani- cally (grinded) and the surface dedusted. Screed grinding accelerates the process of drying.
Cement and anhydrite screeds on floor heatingAppropriately heated and primed with ATLAS UNI-GRUNT, ATLAS UNI-GRUNT ULTRA or ATLAS UNI-GRUNT PLUS
TerrazzoDe-grease the surface thoroughly, in case of waxed terrazzo remove the top layer or whole layer and execute a new one. Prime with ATLAS ULTRAGRUNT.
Walls made of silicate or ceramic bricks and hollow blocks, cellular concreteLevelling coat required (plaster). Direct fixing onto rough wall is possible in case of appropriate substrate dimensional tolerance.
In such case it is necessary to execute full joint wall (or re-fill the joints) and repair any gaps or irregularities with ready-to-use mortars. Prime with ATLAS UNI-GRUNT.
Cement and cement-lime plasters of ready-to-use ATLAS mortarsStabilized min. 3 days* for each 10 mm of thickness; optimum moisture content < 4% by weight.
Other cement and cement-lime plastersStabilized min. 7 days*. Prime with ATLAS UNI-GRUNT.
Gypsum plastersPrime with ATLAS UNI-GRUNT.
If gypsum plaster is applied in
a wet room it should be thoroughly protected against moisture.
If dampness has form of short term action or moderate water splash, then the plaster should be coated with a preparation improving resistance against damp penetration, e.g. ATLAS GRUNTO-PLAST.
Substrates levelled with ATLAS ZW 330 mortarStabilized min. 5 h for layer thickness 5 mm. Stabilized min. 10 h for layer thick- ness 10 mm. Stabilized min. 20 h for layer thickness 20 mm. Stabilized min. 48 h for layer thickness above 20 mm.
ConcreteStabilized min. 21 days; optimum moisture content < 4% by weight. Remove residues of formwork oils and other substances which would impair adhesion. Prime with ATLAS ULTRAGRUNT. Holes, cracks and other gaps should be filled with ATLAS TEN-10 or ATLAS ZW 330 mortars.
Oil paints and resin lacquers coatingsCoatings of poor bonding to the substrate should be mechanically removed. Stable, well bonded coatings: grind, dust; prime oil coatings with ATLAS ULTRAGRUNT. Remove any gypsum fillers used for substrate evening.
OSB boards and wooden floors – the layer composition should be designed and executed in the way excluding the possibility of deformation which may lead to the cladding damage-check the boards type, on floors one may use boards OSB/3 and OSB/4 (acc. to PN-EN 300:2007), min. 25 mm thick, on walls
– min. 18 mm thick,
- check the superstructure stability, boards must not move under operation load; fix additional, stiffening boards layer, if needed, - matt the surface with 40-60 sand paper, - dedust the surface.
Existing ceramic or stone tiles- check bonding to the substrate of the existing cladding by tapping; individual loosening tiles must be removed,
- clean and de-grease the existing tiles surface, - matt glazed tiles with
a diamond grinder,
- dedust the surface - prime with ATLAS ULTRAGRUNT
View other products by ATLAS here.
Brands

Units

25Kg bags

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “ATLAS GEOFLEX Gel Tile Adhesive 25Kg – Pallet Deals & Bulk Buy – Highly Flexible 2-15 MM GREY / WHITE”

There are no reviews yet.

 

Buy The Pallet - Tile Adhesive and Floor Levellers Discount Store

5.0Out of 5 stars

Overall rating out of 16 Google reviews

Phil Down
3 hours ago

They actually answered the phone, were polite, knowledgeable and the order was delivered in full and on time. Would fully recommend both on price and service. Thank you.

Dom
3 weeks ago

BTP very helpful in supplying a pallet of floor leveller. I needed it on the Saturday, but didn’t want it sitting on the driveway for several days. I called and they recommended ordering for Thursday to give a day’s grace in case of any delivery issues. In the event the pallet arrived on Thursday as requested. Reliable and good value

Gary Harper
2 months ago

Great service, great price and great communications. We will definitely use Buy The Pallet again

Adrian W
4 months ago

Great service and delivery! Ordered all that I needed in one go and it was delivered to the back door wrapped and protected from the snow! Pallet even made it so that the goods were dry off the ground.

Stephen Tucker
4 months ago

Great customer service and at an unbeatable price. All delivered on the day I needed it.

Boon Teo
4 months ago

Great prices with a good ranges of products . Customer Service is excellent!

Max Simpson
5 months ago

Very helpful!

Neil Salih
3 years ago

Peter Bostock
3 years ago

I purchased a pallet of these and I am very impressed from ordering to receiving my pallet and the delivery guys were very helpful as well .I will definitely recommend and use this company again .Highly recommend

Kev in
3 years ago

Amazing knowledge and great prices! Definitely using these guys on a regular basis for my pallet deals on levellers and adhesive

Rob Faulkner
3 years ago

Fantastic experience with Buy The Pallet. Everything I needed to complete a large flooring project, quick delivery & quality products.

Richard Fairlie
3 years ago

Great service and really good pricing! Super fast delivery and really lovely guy!

Marc. T
3 years ago

Very helpful