Larsen FiberFlex Semi-Rapid Set+ is a specially formulated, fully flexible, S1 rated, microfibre reinforced, non-slip, cement-based tile adhesive. It is suitable for large format panels, porcelain, ceramic, and natural stone tiles. It is suitable for beds of 3-20mm, interior, exterior, floor, and wall applications.
£624.90 – £707.50 +VAT
Coverage: Approx 4 kg/m2 @ 3 mm bed
| FORM | Powder |
| STANDARD COLOUR(S): | White or Grey |
| HAZARD INFORMATION: | IRRITANT – Consult Safety Datasheet before use |
| CLEANING: | Clean tools, equipment etc. using warm water. Mechanical means are necessary when the product has set. |
| PACKAGING | 20 kg multiwall, sealed paper sacks |
| STORAGE CONDITIONS: | Store in sealed containers in dry conditions, protected from extremes of temperature |
| SHELF LIFE: | 6 months in unopened manufacturer’s packaging |
| MIX PROPORTIONS: | Mix 20 kg powder with approx. 5 – 6 L water depending on application |
| POT LIFE: | Approx. 2 Hours @ 20°C |
| SETING TIME: | Approx. 4-5 hours @ 20°C |
| APPLICATION TEMPERATURE: | +5°C to +30°C |
| BED THICKNESS: | 3- 12 mm (up to 20 mm in small isolated areas) |
| TIME TO TRAFFIC: | Grout after 6 hours Full Traffic after 12 hours Light Foot Traffic after 6 hours |
| COVERAGE: | Approx 4 kg/m2 @ 3 mm bed |
| TENSILE ADHESION STRENGTH: | ≥1 MPa under all test conditions |
| OPEN TIME: | ≥30 min |
| SLIP: | ≤0.5 mm |
| TRANSVERSE DEFORMATION: | ≥2.5 mm |
| CLASSIFICATION: | EN12004 Type C2 TE S1 |
All substrates must be suitably dry and comply with the recommendations in the British Standards and TTA Guidance documents. All substrates should be clean and thoroughly sound; they should be free from standing water, oils, grease, dust, loose particles or any other contaminants which may interfere with adhesion.
Gypsum Based Screeds Gypsum based screeds require mechanical preparation by buffing, vacuuming etc. If an underfloor heating system is present, it must have been fully commissioned up to temperature and the screed must be tested to ensure it is dry (less than 0.5% moisture content measured by CM). All gypsum-based screeds should be primed as follows: first coat Larsen Acrylic Primer diluted 1:1 with water and allowed to dry; second coat Acrylic Primer applied net and allowed to dry fully.
Gypsum Plaster Gypsum plaster on walls is suitable for a weight of tiles and adhesive of up to 20 kg/m2. Plaster should not be dusty or overly polished and should be primed with Larsen Acrylic Primer.
Underfloor Heating New heating systems must have been trialled at a high temperature for a period of at least 48 hours in advance of tiling. Ensure the heating is turned off at least 48 hours before any tiling work is carried out and not turned on until at least 7 days after the work has been completed. Heating should be turned on at the lowest setting and the temperature increased by no more than 5 ̊C per 24 hours. Particular attention should be given to ensure there is adequate provision for movement joints in the tiling.
Timber Substrates There have been changes to recommended guidance on tiling onto timber substrates, for example, timber sheet materials on walls are no longer accepted as a suitable substrate for tiling. Please consult current standards, recommendations and TTA advice before tiling onto timber. Timber substrates must be sufficiently rigid and supported to be free from excessive deflection under expected loads. Ensure adequate ventilation exists beneath the floor. Ensure all new wood (including joists) is ‘dry’ and conditioned. The floor should be designed to accommodate both seasonal changes in moisture and the changes caused by step changes in heating. Extra joists/noggins should be added to strengthen the floor as required. In wet areas timber substrates must be suitably tanked. On floors, existing floorboards should be overboarded. Plywood used for overboarding must be at least 15mm thick exterior grade. Boards should be free from any wax or other coating which may impair bond. Ensure surface is free from contamination and that the backs and edges of all boards are sealed against moisture ingress. Boards should be laid broken-bonded with the long edges running at right angles to the joints between the existing boards and screwed to joists and existing boards at 300 mm centres.
Movement Joints It is important to ensure that there is adequate provision of movement joints in all wall and floor tiling. It is recommended to follow the guidance provided in BS5385, by the TTA and by proprietary joint manufacturers. Ideally, movement joints should be detailed by the designer at the outset. As a guide in external applications max bay size should be 10 m2; internally with underfloor heating, max bay size should be less than 40 m2 and internally on stable substrates without underfloor heating, maximum bay size should be less than 100 m2. All joints in the substrate should also be carried through the tiling. For further information or for situations which are not covered above, consult our website or contact our Technical Dept.
Larsen Acrylic Primer should be used on all gypsum substrates and as required on other porous substrates. On more difficult substrates, Larsen Primer Grip 360 should be used.
The adhesive should be added to clean water and mixed with a suitable slow speed drill and paddle until a lump free mortar is produced. The water ratio can be adjusted depending on the application. For non-slip application on walls, mix 20 kg with approx. 5 L water. For full wettability and bedding on floors, mix 20 kg with up to 6 L water. The amount of water to be added, is an approximate guide. It is possible to obtain mixtures of variable consistency depend on the application. The mixed adhesive is usable for up to 2 hours depending on site temperature and conditions. Do not attempt to remix adhesive or add extra water after it has begun to stiffen as this will cause a loss in performance.
The mixed adhesive should be applied to dry areas on walls using a suitable notched trowel and applied by solid bed on wet areas on walls, on all exterior tiling and on all floor tiling. It is recommended that trowelling is carried out in straight lines rather than ‘swirls’. In addition, when fitting very large format tiles, it is highly recommended to also fully skim the back of the tile with a thin layer of adhesive. Tiles should be placed with a firm twisting action before the adhesive has skinned over, i.e. within the open time of up to 30 min. Regularly check to ensure adequate contact between adhesive, tile and substrate. ‘Dot and Dab’ method of fixing is never acceptable.
Only grout when the tile adhesive has set. Typically this is within 6 hours.
‘Dot and Dab’ method of fixing is not suitable. Tiles should not be fixed to wooden substrates externally or in wet areas. Excessive deflection/movement resulting from incorrect preparation will result in cracking of tiles and/or debonding. Floating Timber and Laminate floors are not recommended substrates for direct fixing of rigid floor finishes. Pale coloured marble/porcelain can be translucent and dark coloured adhesive can sometimes show through. If in doubt we would always recommend tiling a small trial area using a white adhesive and back buttering the tiles to ensure a uniform adhesive coverage. Cement-based products will take longer to harden and set at lower temperatures, and should not be used below 5°C. All tiling should be carried to current best practice, including British Standards and TTA Guidance documents.
| Brands |
|---|
You must be logged in to post a review.
Fantastic customer service and fast delivery, highly recommend
Great prices and a super quick delivery turnaround. Communication was perfect aswell. So much so I’ve ordered again.
They actually answered the phone, were polite, knowledgeable and the order was delivered in full and on time. Would fully recommend both on price and service. Thank you.
BTP very helpful in supplying a pallet of floor leveller. I needed it on the Saturday, but didn’t want it sitting on the driveway for several days. I called and they recommended ordering for Thursday to give a day’s grace in case of any delivery issues. In the event the pallet arrived on Thursday as requested. Reliable and good value
Great service, great price and great communications. We will definitely use Buy The Pallet again
Great service and delivery! Ordered all that I needed in one go and it was delivered to the back door wrapped and protected from the snow! Pallet even made it so that the goods were dry off the ground.
Great customer service and at an unbeatable price. All delivered on the day I needed it.
Great prices with a good ranges of products . Customer Service is excellent!
Great prices with a good ranges of products . Customer Service is excellent!
Companies like this a rare, great quick service, great price and easy to do business with. Will definitely use them again for all my supplies.
First class service, good price, fast delivery and the chap at the end of the phone knew what he was on about. Highly recommend and will use them again.
I purchased a pallet of these and I am very impressed from ordering to receiving my pallet and the delivery guys were very helpful as well .I will definitely recommend and use this company again .Highly recommend
Amazing knowledge and great prices! Definitely using these guys on a regular basis for my pallet deals on levellers and adhesive
Great service and really good pricing! Super fast delivery and really lovely guy!
Fantastic experience with Buy The Pallet. Everything I needed to complete a large flooring project, quick delivery & quality products.
Very helpful!
Very helpful
There are no reviews yet.