Everbuild Facades One Coat GPR 25Kg General Purpose Render – Pallet Deals and Bulk Buy

Everbuild Facades One Coat GPR extended information

Consumption: 25 kg of Everbuild Facades One Coat GPR will cover 1.7 – 1.8 m2 at 10 mm thickness

Usage

Masonry and walls constructed from the following:

• Ultra-lightweight, lightweight & dense aggregate concrete blocks
• Brick
• Clay blocks e.g. porotherm
• Standard low and normal density lightweight aircrete blocks
• Breeze blocks
• Stone/ rubble stone
• Shuttered concrete
• Expanded clay insulation blocks
• Clean, sound, well adhered existing render
• Dry-stacked inter-locking modular wall units e.g. Durisol recycled timber blocks

These substrates will require a suction control coat of Everbuild 503 SBR prior to applying Everbuild Facades One Coat GPR

Advantages

• One coat application
• Overpaintable
• Suitable for masonry and concrete walls
• For internal and external use
• Weather resistant
• Breathable

Everbuild Facades One Coat GPR Product Information

Everbuild Facades One Coat GPR Technical Information

Everbuild Facades One Coat GPR Application Information

Limitations

• Avoid applying a thin base coat and thicker top coat as the level of shrinkage to the thicker top coat could cause the render to delaminate from the base coat
• To avoid shade variations, always apply and finish the render application to whole elevations at the same time
• Do not apply Everbuild Facades One Coat GPR to weak mortar or plaster coated constructions
• Do not use this product on exposed vertical substrates with a backward incline above 10° – a backward incline may affect water run off
• Do not apply on painted substrates
• If applied to concrete, it must not be covered with tiling, as additional waterproofing may be required

Substrate Instructions

SUBSTRATE QUALITY / PRE-TREATMENT

• Substrates must be clean, sound, dust free, and free of any material that may prevent adhesion
• Ensure the substrate is free from oil and grease
• Remove all traces of plaster, paint etc.
• If the surface has limited / no porosity, e.g. shutter concrete or wet/patchy substrates, or ones involving several substrates, prime with Everbuild® 503 SBR Bond diluted 3:1 with clean water and allow to dry
• Then add a bonding coat of 1:1 Everbuild 503 SBR Bond with clean water mixed with 1.5 parts cement and apply Everbuild Facades One Coat GPR whilst still tacky. Alternatively use Everbuild 507 Rendagrip or Parex Micro Gobetis 3000 following instructions.

MIXING

Mix at a ratio of 4.5-5.5 litres clean water to 25 kg bag of Everbuild® Facades One Coat GPR

Mix for approx. 3-5 minutes with a spiral action mixer

APPLICATION

Everbuild Facades One Coat GPR should be applied following EN13914-1 code of practice.
For weatherproofing concrete blocks and masonry substrates:

• Apply the first coat of Everbuild Facades One Coat GPR levelled and lined to a depth of 10 mm thick and leave with a toothed trowel finish
• For the second coat, apply a minimum 5 mm coat of product and finish using a stainless steel trowel or float depending on the desired effect. To apply a base coat finish for receiving tiling or brick slip finish, apply one compact 15mm thick coat and leave with toothed trowel finish

For applying onto waterproof substrates e.g. concrete

• Apply a single coat between 7-8 mm thick, float-finishing as you progress using a stainless steel trowel, wooden, plastic or sponge float finish depending on the finish desired
• For thicker applications, apply 2 coats as for float finished waterproofing coatingFor guidance regarding machine application please contact the Parex technical department.

Everbuild Facades One Coat GPR – CLEANING OF TOOLS

Clean immediately with fresh water

Everbuild Facades One Coat GPR Technical Video