Mapei Mapeheat Membrane – Uncoupling and Waterproofing Membrane – Underfloor Heating – Bulk Buy Deals

Mapei Mapeheat Membrane extended information

Packaging and Approximate Coverage

Industry Standards and Approvals

• ANSI: Passes All8.12 standard (Crack Isolation Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation) and A118.10 standard (Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation)
• ASTM: C627 (Robinson) service rating for “Extra Heavy”

Where To Use

• Use under ceramic and natural stone tile in interior residential spaces such as kitchens, bathrooms, shower floors and three-season rooms.
• Use as a substrate for self-levellers under engineered wood, sheet vinyl, luxury vinyl tiles, luxury vinyl planks, laminate flooring and mosaic tile.

Limitations

• Do not use over cracks or control joints subject to out-of-plane movement, or where in-plane movement exists greater than 1/8″ (3 mm).
• Do not cover expansion joints. Refer to the most current TCNA Handbook, Method EJ171, or TTMAC Tile Installation Manual, Detail 301MJ.
• Do not use as a replacement layer of plywood or cement board under natural stone.
• Do not use over substrates containing asbestos, plank wood flooring, presswood, particleboard, chipboard, pressure- or oil-treated plywood, Lauan, Masonite, self-stick tile, laminate, metal, fiberglass or similar dimensionally unstable materials.
• Do not use for submerged applications or for floors subject to standing water.
• Do not use in exterior applications.
• Do not use premixed products to set tile over Mapeheat Membrane.
• Do not install moisture-sensitive tile or stone with water-based setting materials. Note: On occasion, dimensionally weak natural-stone tile that normally would not be categorized as moisture-sensitive such as travertine, limestone, marble and agglomerates) can exhibit doming, cupping or curling when installed over impervious membranes such as Mapeheat Membrane.
• Do not use on bituminous substrates.
• Do not use on highly flammable material.
• Do not use with solid, hardwood flooring
• Before the installation of mosaic tile, a self-leveller must be applied over Mapeheat Membrane at a minimum thickness of 1/4″ (6 mm) above the highest point of the membrane.

Suitable Substrates

• Cured or young concrete. When used over young (green) concrete, the concrete must have cured for at least 7 days and be suitable to support tile installation traffic as determined by the project design professional, construction manager or general contractor.
• Cement mortar beds and levelling coats
• Cement backer units (BUs) – see manufacturer’s installation guidelines
• Industry-approved, exterior-grade plywood and APA Sturd-I-Floor, Exposure 1 OSB (in interior, dry areas only).
  Regarding deflection requirements, refer to the local building code; to the TCNA Handbook, Field Installation Requirements, subsection “Maximum Allowable Deflection for Floor System and Substrate;” to the TTMAC 09 30 00 specifications guide; and to ANSI A108.01, Section 3.4.
• Existing, well-bonded ceramic tile and dimensionally stable natural stone
• Existing, structurally sound vinyl floor without any foam or under cushioning mat
• Existing, cement terrazzo floors

Consult MAPEl’s Technical Services Department for installation recommendations regarding substrates and conditions not listed.

Surface Preparation

• All suitable substrates must be smooth, structurally sound and free of any substance that could prevent or reduce proper bond and/or affect product performances.
• If moisture in the substrate would be an issue for the intended flooring, such as moisture-sensitive engineered wood and LVT, install a MAPEl moisture barrier product on the substrate before installing
  Mapeheat Membrane.
• Gypsum-based patching or leveling compounds may leave a dusty residue on the surface. Clean the dusty substrate before applying primer and an approved MAPEl adhesive. See the technical bulletin “Tiling over gypsum” in the Related Documents section of the Tile & Stone Installation Systems page on MAPEl’s Website.
• Wood subfloors must be prepared according to ANSI A108.01 and A108.02; to the TCNA Handbook, Field Installation Requirements, subsection “Maximum Allowable Deflection for Floor System and Substrate;” and to the TTMAC 09 30 00 specifications guide.
• Do not use chemical means (acid etching or stripping) to prepare approved substrates. Use mechanical methods only.
• Concrete substrates must be flat, smooth and absorptive. To remove any bond-inhibiting materials, concrete substrates should be mechanically prepared to obtain the International Concrete Repair Institute (ICRI) concrete surface profile (CSP) #2.

See the “Surface preparation requirements” reference guide in the Related Documents section of the Tile & Stone Installation Systems page on MAPEl’s Website.

Mapei Mapeheat Membrane Product Application

Read all installation instructions thoroughly before installation.

• Apply Mapeheat Membrane when substrate and ambient temperatures are between 50°F and 95°F (10°C and 35°C).

Bonding Mapeheat Membrane to the substrate

1. Select an appropriate MAPEI latex polymer-modified mortar with ISO 13007 classification C2E or better, and meeting ANSI A118.4 or ANSI A118.11 industry standards or better.
2. Pre-cut and dry-fit Mapeheat Membrane in place, and then set aside.
3. Apply the mortar to the substrate. If the substrate is existing tile, stone, vinyl or terrazzo, apply a primer such as MAPEl’s ECO Prim Grip before applying the mortar.
4. Lay the previously cut portion of Mapeheat Membrane over the wet mortar, fabric side down.
5. Lay the next sheet of Mapeheat Membrane, taking care to align it with the previous one, without overlapping. Align the square reliefs.
6. For a proper bond between Mapeheat Membrane and the floor, use a 50-l. (22.7-kg) or heavier roller over the installed membrane. For smaller pieces of membrane, use a wood float, steel trowel or hand roller to apply pressure.
7. After rolling, as the installation progresses, clean off any excess mortar that may have squeezed up through the seams between the membrane sections.
8. Allow the mortar to cure.

Installing the electrical cable

For complete cable installation instructions, refer to the Technical Data Sheet (TDS) for Mapeheat Cable at www.mapei.com

Waterproofing (optional for installing ceramic tile)

1. After the cable has been properly installed, use a 1/4″ × 3/16″ (6 × 4.5 mm) V-notched trowel to apply the same mortar used to bond the membrane to the substrate. The mortar should be keyed in over the adjoining seams with the trowel’s flat side. Be sure to fill in any holes or voids, taking care not to damage the heating cable with the trowel.
2. Mapeguard® ST or Mapeguard WP ST sealing tape will be applied over the seams that are covered with wet mortar. First, center the seam tape over the seams with at least 2″ (5 cm) on each side of a seam. Then apply the seam tape, working the sealing tape into the mortar with a grout float or the trowel’s flat side while the mortar is still workable.
3. To waterproof around the walls of the installation area, take a pre-measured length of the seam tape and fold it in half along its length. One side of the fold will be adhered to the floor, and the other side will be adhered up the wall. To accomplish this, follow the installation methods detailed in steps 1 and 2.
4. Next, embed the seam tape into the mortar with a grout float or the trowel’s flat side, taking care not to puncture the membrane or damage the heating cable.
5. Mortar should be under the seam tape only. Use a damp sponge to clean off any visible excess mortar on Mapeheat Membrane so as not to hinder bonding during flooring installation.
6. Flood testing should be performed before installing the finished flooring. Do not flood-test while the heating cable is activated.

Installation of ceramic/porcelain tile and stone

1. For regular installations, utilize the same mortar used to bond Mapeheat Membrane to the substrate. For fast-track installations, use one of MAPEl’s rapid-setting mortars with MAPEl’s Ultracolor® Plus FA grout. For large and heavy tiles, use a MAPEl mortar that meets the ANSI A118.4 or ANSI A118.15 standard.
2. Mix the mortar to a consistency on the high end of the recommended water range for mixing.
3. Select an appropriate trowel per instructions on the mortar’s TDS. Use the trowel’s flat side to fill the cavities of Mapeheat Membrane with mortar. Alternatively, a rubber grout float can be used to fill the cavities with mortar.
4. Use the trowel’s notched side to apply a tile-setting layer of the same mortar over the prefilled Mapeheat Membrane. If a heating cable was inserted into the membrane, be careful not to damage the cable with the trowel. Spread only as much mortar as can be covered before the mortar skins over. Open times vary with jobsite conditions and mortar choice.
5. Begin to install the tile/stone. Occasionally remove and check some tiles for proper coverage per ANSI guidelines.
6. For waiting times before grouting and protection from light foot traffic, refer to the TDSs of the MAPEI tile-setting mortar and grout being utilized. Depending on site conditions, tile size, temperature and humidity, waiting times may need to be extended.
7. When cleaning out grout joints before grouting, be careful not to damage the cables that may be underneath.
8. Wait at least 72 hours after the completed installation of tile before reactivating the heating cable.

Installation of moisture-sensitive tile and stone

1. To prefill the cavities of Mapeheat Membrane, utilize a polymer-modified mortar approved for moisture-sensitive tile/stone.
2. Mix the mortar to a consistency on the high end of the recommended water range for mixing.
3. Select an appropriate trowel. Use a trowel’s flat side to fill the cavities of Mapeheat Membrane with mortar.
   Alternatively, a rubber grout float can be used to fill the cavities with mortar.
4. Allow the mortar to cure overnight.
5. Use the trowel’s notched side to apply a tile-setting layer of Kerapoxy ® 410 100%-solids, epoxy setting mortar over the prefilled Mapeheat Membrane, following directions on the TDS for Kerapoxy 410.
6. Begin to install the tile/stone. Occasionally remove and check some tiles for proper coverage per ANSI guidelines.
7. For waiting times before grouting and protection from light foot traffic, refer to the TDSs for Kerapoxy 410 and the grout being utilized. Depending on site conditions, tile size, temperature and humidity, waiting times may need to be extended.
8. When cleaning out grout joints before grouting, be careful not to damage the cables that may be underneath.
9. Wait at least 72 hours after the tile installation before reactivating the heating cable.

Installation of alternate floor coverings (engineered wood, sheet vinyl, luxury vinyl tile, luxury viny_plank, laminate).

1. Apply any MAPEI self-leveler over Mapeheat Membrane at a minimum thickness of 1/4″ (6 mm) above the highest point of the membrane.
2. Using a primer as a pre-step is not necessary.
3. Allow the self-leveler to cure.
4. Install floor covering using an appropriate adhesive according to its TDS.
5. Wait at least 72 hours after the flooring installation before reactivating the heating cable.

Note: Tile/stone is the most efficient floor covering for providing maximum heat conductivity and thermal output per square foot (meter). Because other floor-covering types may not transfer heat at the same rate, they may not warm the floor to the same degree as ceramic tile and stone will, unless heating cables are set at a higher temperature.

Caution: The technical data sheet and/or installation instructions for any chosen floor covering must confirm compatibility with radiant floor-heating systems. In addition, the temperature of the heating cable must not exceed the floor covering’s maximum allowable temperature.

Expansion Joints

• Honor expansion joints through Mapeheat Membrane, tiles and grout per tile industry standards.
  When necessary, cut tiles along both edges of the expansion joints. Do not allow tiles and mortar to overlap the expansion joints.
• Provide for movement joints as required by TCNA Method EJ171, or by TTMAC Specification Guide 09 30 00,
  Detail 301MJ

Protection

• Protect Mapeheat Membrane from direct exposure to sunlight or extreme heat.
• Provide for dry storage on site at between 40°F and 95°F (4°C and 35°C). Deliver materials at least 24 hours before application.
• For information about waiting before grouting and protecting from light foot traffic, refer to the TDSs of the MAPEI tile-setting mortar and grout being utilized. Depending on site conditions, temperature and humidity, the waiting times may need to be extended.
• Protect the flooring installation from heavy traffic or rolling loads for at least 72 hours if using a rapid-set mortar and 7 days if using a large-and-heavy-tile mortar.
• Protect installation from contamination and damage before and during tilework.
• Always provide proper protection of finished floors when heavy equipment (such as fork lifts or scissor lifts) is to be used over installations with sheet membrane underlayments during construction.

Mapei Mapeheat Membrane product performance properties

Mapei Mapeheat Membrane Shelf Life and Product Characteristics

Mapeheat Membrane Technical Video