Tilemaster Trade Flow extended information
COVERAGE: 20kg bag and 5 L liquid will cover approximately 5 sq. metres at 3mm depth
Once mixed, Tilemaster Trade Flow will remain workable for 20 – 25 minutes and it will accept light foot traffic after 2 hours in ideal conditions. Decorative floor coverings can be installed after 12 hours. Trade Flow can be applied from depths of 2 – 12mm in one application. When mixed with additional aggregate, Tilemaster Trade Flow can be applied up to 30mm thick.
Tilemaster Trade Flow technical data:
| Screed classification | CT-C20-F6 to EN13813:2002 |
| Working time @ 23oC | 20 – 25 minutes |
| Time to foot traffic @ 23oC | 2 hours |
| Application thickness | 2mm – 12 mm |
| Compressive strength N/mm2 (BS EN 13892-2) | 1 day > 10.0
7 day > 15.0
28 day > 20.0 |
| Flexural strength N/mm2 (BS EN 13892-2) | 1 day > 3.0
7 day > 5.0
28 day > 6.0 |
| Coverage | A 20kg bag and 5.0Ltr liquid unit will cover 5.0m2 at 3mm thickness |
| Flow properties using 30mm x 50mm flow ring | 135mm – 150 mm |
| Minimum application temperature | 5oC |
| Shelf life | Stored correctly the powder component has a shelf life of 6 months and 12 months for the latex liquid |
| Colour | Powder – Grey
Liquid - White |
| Pack size | Bag - 20kg
Liquid – 5 Litres |
| Note | All work must be carried out in accordance with British Standard Code of Practice. |
Tilemaster Trade Flow ADVANTAGES:
- Excellent flow properties
- Apply from 2 – 12mm in one pour
- Light foot traffic after 2 hours
- Apply floor coverings after 12 hours
- Moisture tolerant
- Ideal for underfloor heating systems
- Ideal for plywood overlay
- Low odour
- Protein free
Tilemaster Trade Flow IDEAL FOR:
- Sand/Cement Screed
- Concrete
- Plywood Overlay (15mm min)
- Electric Underfloor Heating
- Water/Wet System Underfloor Heating
- Tile Backer Boards
- Existing Ceramic, Porcelain and Natural Stone Tiles
- Flooring Grade Asphalt & Bitumen
- Anhydrite Screeds
- Fibre Cement Sheet
- Existing Vinyl Tiles
- Steel/Metal Surfaces
- Fibreglass
| Brands | TileMaster |
|---|
| Colour | Grey |
|---|
| Units | 20Kg bags and 4.5Kg additive |
|---|
COVERAGE: 20kg bag and 5 L liquid will cover approximately 5 sq. metres at 3mm depth
PREPARATION OF TILEMASTER TRADE FLOW:
Before starting, all substrates must be clean, dry and strong enough to support the weight of the leveller and the final floor covering being applied. Remove all dust, dirt, oil, grease and other contaminants that may affect adhesion. Where traces of adhesive residue remain, these must be checked to ensure that they are not softened with water and that they are strong, sound and well adhered to the substrate in order to receive a levelling compound.
When installing moisture sensitive floor coverings, the concrete or sand/cement screed should be confirmed dry by consistent moisture readings; <75% relative humidity (RH) or <0.5% residual moisture when tested in accordance with BS 8203. Where a structural damp proof membrane is not present or where rising damp and/or residual moisture results in moisture readings up to 98% RH, a liquid damp proof membrane such as Tilemaster Fast One Coat DPM must be applied before the application of Tilemaster Trade Flow. Surface laitance should be removed from concrete and sand/cement screed surfaces prior to application.
All substrates require priming prior to the application of Tilemaster Trade Flow. Priming the substrate will minimize the risk of pinholes forming, allow for the best flow properties and also prolong the working time of the product. Priming the substrate prior to application is considered “best practice”. For recommended priming dilution rates please refer to Page 3 of this data sheet.
Prior to levelling timber substrates ensure that timber boards are securely screwed down and firmly fixed. Where timber substrates are sufficiently rigid but uneven or worn, Tilemaster Trade Flow can be used to smooth and level the timber substrate prior to over-boarding with plywood overlay or a tile backer board. If following this process, allow Tilemaster Trade Flow to cure before fitting the overlay boarding.
MIXING AND APPLICATION:
Shake the pre-gauged bottle of liquid polymer and pour into a suitable clean mixing vessel. Add the powder component slowly whilst mixing with an electric paddle and continue to mix for a further 2 minutes until a smooth and lump free consistency is obtained, allow the product to stand for a further 2 minutes prior to application. Once mixed do not add further polymer liquid or water.
N.B. Once mixed, Tilemaster Trade Flow will remain workable in the bucket for 20 – 25 minutes at 20°C.
Pour a small quantity onto the prepared surface and trowel down lightly to a depth between 2mm and 12mm. The use of a spiked roller is recommended immediately in order to remove entrapped air and smooth out flow lines. Setting time will depend on atmospheric conditions/temperatures, it will be slowed by lower temperatures and accelerated by higher temperatures.
If the substrate is impervious Tilemaster Trade Flow should be applied to a minimum overall thickness of 3mm. This is to ensure the uniform drying of Tilemaster Trade Flow.
Clean tools immediately after use with clean water.
SETTING AND COVERING:
In ideal conditions, Tilemaster Trade Flow will accept light foot traffic after 2 hours. Tilemaster Trade Flow must be left to dry before applying the final decorative surface flooring. This is typically after 12 hours for decorative flooring such as vinyl and 4 hours for ceramic tiles, however, this can vary depending on the choice of surface flooring. Thicker applications may require a longer time to dry prior to applying floor coverings. If there is no air flow within site conditions, the drying time may be restricted. The critical moisture content for the flooring in question must be observed.
