, , ,

Tilemaster – Standard Set Extrabond – Standard Setting Polymer Modified Wall & Floor Tile Adhesive – Grey/White (20Kg) Pallet (50bags) Half-Pallet (25bags)


Tilemaster Standard Set Extrabond is:

Standard Set Extrabond is a standard setting, polymer modified cement based wall and floor tile adhesive with increased adhesion and non-slip properties.

It has been specially formulated for fixing a large variety of tiles including:

  • ceramic
  • porcelain
  • natural stone tiles
  • solid substrates such as sand/cement screed, concrete, brick/block and plaster

Formulated to give an extended pot life of 3 – 4 hours, Standard Set Extrabond is ideal where longer working times are required. It is ideal for areas subject to prolonged wet conditions such as showers and wet rooms. It can be used internally and externally and it is unaffected by frost after setting.

When mixed with Flexmaster Additive, Standard Set Extrabond is suitable for fixing to a wider variety of substrates.

Need a bespoke deal or a mixed pallet of products? Tell us what you're looking for -> Mixed Pallet Quote

Spotted a pallet deal cheaper than ours? We can usually beat it! 0333 344 2655 or info@buythepallet.co.uk

~ Free Delivery on Pallets & Half-Pallets, 3-5 Working Days ~

£210.00£395.00 +VAT

£210.00 £294.92 +VAT
£280.00 £367.38 +VAT
£360.00 £470.20 +VAT
£230.00 £322.76 +VAT
£308.00 £391.20 +VAT
£395.00 £510.10 +VAT

More about Tilemaster Standard Set Extrabond:

Coverage: 20kg will cover 5 – 6m² at 3mm thin bed application


  • Suitable for fixing ceramic, porcelain and natural stone tiles
  • Polymer modified for increased adhesion
  • Excellent workability and non-slip properties
  • Extended pot life of 3 – 4 hours, ideal where longer working times are required
  • 3mm – 12mm bed depth
  • Internal and external use


  • Ceramics
  • Porcelain
  • Marble
  • Travertine
  • Limestone
  • Slate
  • Granite
  • Terracotta
  • Mosaics
  • Quarry

Surface / Substrate

  • Sand/Cement Screed
  • Concrete
  • Tile Backer Boards
  • Existing Ceramic, Porcelain and Natural Stone Tiles*
  • Plaster
  • Plasterboard
  • Cement/Sand Render
  • Concrete Brick/Block


Tilemaster Standard Set Extrabond is suitable for use with natural stone tiles but suitability with very porous and sensitive natural stone tiles must be tested prior to use. Confirmation of suitability should be sought from the supplier of the natural stone tiles.


Before starting, all substrates must be clean, dry and strong enough to support the weight of the tiles, tile adhesive and grout. Remove all dust, dirt, oil, grease and other contaminants that may affect adhesion.


Only mix small quantities at a time until you have become accustomed to the nature of the product. Always mix powder to water and mix to a smooth and lump free consistency. As a guide for powder to water ratio, 20kg of powder requires approximately 4.4 – 4.6 litres of water. Never add water after initial mixing, as this will impair the strength of the adhesive. Product that has started to set must be discarded.

N.B. When fixing large format tiles, natural stone tiles and tiles that have deep studs on the back, you must skim the back of the tile with a 1 – 2mm layer of adhesive, this is referred to as back buttering. This will significantly improve the bond strength.

On a flat, even substrate where dry conditions exist, apply adhesive to substrate as a thin floated coat at a uniform thickness of 3 – 6mm and then rib / comb out using a suitable notched trowel. Where substrate conditions do not allow thin bed fixing, Tilemaster Standard Set Extrabond can be applied to a maximum bed thickness of 12mm. Ensuring the adhesive is still moist, bed tiles into adhesive using a twisting action ensuring full coverage of adhesive between tile and substrate. Regular checks should be made to make sure that there are no voids in the adhesive bed.

N.B. When fixing tiles externally or in areas subject to prolonged wet conditions, you must ensure that you achieve 100% adhesive coverage between tile and substrate.

Clean surplus adhesive from the tiles and joints as soon as possible as set adhesive will prove very difficult to remove later.

Clean tools after use with water.


Do not start grouting until the adhesive has set. This time can vary depending on temperature and site conditions. Impervious surfaces may extend the set time. In ideal conditions grouting can begin after 24 hours.




White, Grey


20Kg bags

Coverage: 20kg will cover 5 – 6m² at 3mm thin bed application