, , ,

Tilemaster – Light Weight Standard Set – Flexible Standard Setting Wall & Floor Tile Adhesive – White (15Kg) Pallet (48bags) Half-Pallet (24bags)


Tilemaster Light Weight Standard Set is:

Light Weight Standard is a polymer modified, flexible standard setting cement based wall and floor tile adhesive made using special lightweight fillers and additives to produce excellent non-slip properties, improved workability and greater than 60% extra coverage over traditional sand/cement based adhesives.

Light Weight Standard has been specially formulated for fixing a large variety of tiles including ceramic, porcelain and natural stone tiles to substrates subject to limited movement and/or vibration such as plywood overlay, timber framework and underfloor heating systems as well as for fixing to solid substrates such as concrete and sand/cement screed. Light Weight Standard provides an extended pot life of 3 – 4 hours and it is ideal for areas subject to prolonged or permanent wet conditions such as swimming pools and wet rooms. Light Weight Standard can be used internally and externally and it is unaffected by frost after setting.

Need a bespoke deal or a mixed pallet of products? We can quote you and keep the big savings ... go here to tell us what you need -> Mixed Pallet Quote

Spotted a pallet deal cheaper than ours? We can usually beat it! 0333 344 2655 or info@buythepallet.co.uk

~ Free Delivery on Pallets & Half-Pallets, 3-5 Working Days ~

£415.00£775.00 +VAT

£415.00 £499.32 +VAT
£775.00 £948.28 +VAT

More about Tilemaster Light Weight Standard Set:

Coverage: 15kg will cover 10 – 12m² at 3mm thin bed application


  • Greater than 60% extra coverage over traditional sand/cement adhesives
  • Fantastic non-slip properties
  • Minimum of 50% lighter per m²
  • Contains 20% recycled material
  • Ideal for timber substrates
  • Ideal for use above underfloor heating systems
  • Suitable for fixing ceramic, porcelain and natural stone tiles
  • Extended pot life of 3 – 4 hours, ideal where longer working times are required
  • 3mm – 12mm bed depth


  • Ceramics
  • Porcelain
  • Marble
  • Travertine
  • Limestone
  • Slate
  • Granite
  • Terracotta
  • Mosaics
  • Quarry

Ideal For:

  • Sand/Cement Screed
  • Concrete
  • Plywood Overlay (12mm min)
  • Electric Underfloor Heating
  • Water/Wet System Underfloor Heating
  • Tile Backer Boards
  • Existing Ceramic, Porcelain and Natural Stone Tiles*
  • Flooring Grade Asphalt & Bitumen*
  • Anhydrite Screeds
  • Plaster
  • Plasterboard
  • Cement/Sand Render
  • Concrete Brick/Block
  • Existing Vinyl Tiles*
  • Epoxy DPM*


Tilemaster Light Weight Standard Set is suitable for use with natural stone tiles but suitability with very porous and sensitive natural stone tiles must be tested prior to use. Confirmation of suitability should be sought from the supplier of the natural stone tiles.


Before starting, all substrates must be clean, dry and strong enough to support the weight of the tiles, tile adhesive and grout. Remove all dust, dirt, oil, grease and other contaminants that may affect adhesion.


Only mix small quantities at a time until you have become accustomed to the nature of the product. Always mix powder to water and mix to a smooth and lump free consistency. As a guide for powder to water ratio, 15kg of powder requires approximately 8.0 – 9.0 litres of water. Never add water after initial mixing, as this will impair the strength of the adhesive. Product that has started to set must be discarded.

NB. When fixing large format tiles, natural stone tiles and tiles that have deep studs on the back, you must skim the back of the tile with a thin 1 – 2mm layer of adhesive, this is referred to as back buttering. This will significantly improve the bond strength.

On a flat, even substrate where dry conditions exist, apply adhesive to the substrate as a thin floated coat at a uniform thickness of 3mm – 6mm and then rib / comb out using a suitable notched trowel. Where substrate conditions do not allow thin bed fixing, Tilemaster Light Weight Standard Set can be applied to a maximum bed thickness of 12mm. Ensuring the adhesive is still moist, bed tiles into adhesive using a twisting action ensuring full coverage of adhesive between tile and substrate. Regular checks should be made to make sure that there are no voids in the adhesive bed.

NB. When fixing tiles externally or in areas subject to prolonged or permanent wet conditions, you must ensure that you achieve 100% adhesive coverage between tile and substrate.

Clean surplus adhesive from the tiles and joints as soon as possible as set adhesive will prove very difficult to remove later.

Clean tools after use with water.


Do not start grouting until the adhesive has set. This time can vary depending on temperature and site conditions. Impervious surfaces may extend the set time. In ideal conditions grouting can begin after 24 hours. If you are tiling an area of limited movement or underfloor heating, you must use a flexible grout such as Tilemaster Grout 3000 or Tilemaster Flexigrout.





15Kg bags

Coverage: 15kg will cover 10 – 12m² at 3mm thin bed application