-0%
,

Tilemaster – Leveller – Self Levelling Floor Compound (20Kg) Grey Pallet (50bags) & Half-Pallet (25bags)

TileMaster

Tilemaster Leveller is:

  • fast setting
  • flexible
  • fibre reinforced self levelling compound.

Leveller is a fast setting and protein free cement based formulation designed for smoothing and levelling subfloors prior to the installation of floor coverings. Leveller can be applied to a depth of 12mm when simply mixed with water or to a maximum depth of 25mm when mixed with 3 – 5mm aggregate. Leveller will accept light foot traffic after 4 hours and after 8 hours ceramic, porcelain and natural stone tiles can be applied. Soft flooring such as linoleum, vinyl and carpet can be applied after 48 hours. Leveller is only suitable for use over solid substrates such as sand/cement screed and concrete.

Need a few bags of Grout as well, no problem click here.Need a bespoke deal? Contact us

Spotted a pallet deal cheaper than ours? We can usually beat it! 0333 344 2655 or info@buythepallet.co.uk


~ Free Delivery on Pallets & Half-Pallets, 2-3 Working Days ~

£208.33£350.07 +VAT

£208.33 £243.50 +VAT
£350.07 £397.50 +VAT

ADVANTAGES:

  • Apply from 2 – 12mm in one pour
  • Apply up to 25mm when mixed with aggregate
  • Light foot traffic after 4 hours
  • Tile after 8 hours
  • Simply mix with water
  • Protein Free

SURFACE/SUBSTRATES:

  • Sand/Cement Screed
  • Concrete
  • Tile Backer Boards
  • Existing Ceramic, Procelain and Natural Stone Tiles (Prime with Prime + Grip)

Technical Data:
Screed classification: CT-C16-F5 to BS EN 13813; 2002
Working time @ 20°C: 20 – 30 minutes
Time to foot traffic @ 20°C: 4 hours
Application thickness: 2 – 12mm when mixed with water, Up to 25mm when mixed with 3 – 5mm aggregate
Compressive strength: 28 day > 16.0 N/mm2 (BS EN 13892-2)
Flexural strength: 28 day > 5.0 N/mm2 (BS EN 13892-2)
Coverage: 20kg will cover 4.2m2 at 3mm thickness
Flow properties: using 30mm x 50mm flow ring 125 – 145 mm
Minimum application temperature: 5°C
Shelf life: Stored correctly this product has ashelf life of 6 months
Colour: Grey
Pack size: 20 kg

Brands

Colour

Grey

Units

20Kg bags

Total Units

40x25Kg bags

COVERAGE: 20kg will cover 4.2m2 at 3mm thickness

 

PREPARATION USING TILEMASTER LEVELLER:

Before starting, all substrates must be clean, dry and strong enough to support the weight of the leveller, adhesive and the final floor covering being applied. Remove all dust, dirt, oil, grease and other contaminants that may affect adhesion. Where traces of adhesive remain, these must be strong, sound and well adhered to the substrate.

The substrate must be confirmed dry by consistent moisture readings; <75% relative humidity (RH) or <0.5% residual moisture content prior to application. Remove any loose or flaking layers. Laitance should be removed from concrete and sand/cement screed surfaces. Sub-floors directly to earth must have a damp-proof membrane.

MIXING AND APPLICATION:

Mix by adding Leveller to clean water, approximately 4.2 – 4.8 litres of water to 20kg of Leveller. We suggest starting with 4.2 litres of water which can then be increased to a maximum of 4.8 litres if necessary. Leveller will flow better at 4.8 litres of water, however, do not exceed 4.8 litres of water per bag of Leveller. Exceeding 4.8 litres of water per 20kg will result in water bleed and therefore extended drying times and a weakened mix.

Mix ideally with an electric paddle until you obtain a smooth and lump free consistency. When mixed allow to stand for 2 minutes and stir again before application. Once mixed, Leveller will remain workable in the bucket for approximately 30 minutes.

Pour a small quantity onto the prepared surface and trowel down lightly to a depth between 2 – 12mm. The use of a spiked roller is recommended in order to remove entrapped air and smooth out flow lines. Leveller will maintain a “wet edge” for 20 – 30 minutes but depending on the porosity of the substrate and ambient conditions, once applied, the drying process can begin after 15 – 20 minutes.

For depths greater than 12mm, aggregate should be added to Leveller for increased economy and performance. Add 3 – 5mm aggregate at a rate of 2 parts Leveller to 1 part aggregate. Add powder to water and use the water additions stated on the product packaging, please note that the water additions may vary slightly depending on the aggregate used. Pour a small quantity onto the prepared surface and trowel down lightly to a maximum depth of 25mm. If you wish to apply a second coat of Leveller, allow the first coat to dry and prime between applications.

Leveller must be left to dry before applying the final decorative surface flooring. This is typically 8 hours for ceramic, porcelain and natural stone tiles and 48 hours for soft flooring such as linoleum and vinyl. The setting time will depend on atmospheric conditions/temperatures, it will be slowed by lower temperatures and accelerated by higher temperatures.

N.B. If there is no air flow within site conditions, the drying time may be restricted.

The critical moisture content for the flooring in question must be observed.