, ,

Tilemaster Eco-3000 – Universal High Temperature Flooring Adhesive 15Kg (cream) – Pallet & Half Pallet – Bulk Buy


Tilemaster Eco-3000 is:

  • high temperature adhesive (ideal for underfloor heating)
  • apply floor coverings in as little as 10 minutes
  • solvent free
  • excellent adhesion
  • high bond strength
  • hard set once cured

Need a bespoke deal or a mixed pallet of products? Tell us what you're looking for -> Mixed Pallet Quote

Spotted a pallet deal cheaper than ours? We can usually beat it! 0333 344 2655 or info@buythepallet.co.uk

~ Free Delivery on Pallets & Half-Pallets, 3-5 Working Days ~

Tilemaster Eco-3000 is:

Tilemaster Eco-3000 is a universal, high temperature, solvent free flooring adhesive suitable for installing a wide variety of floor coverings to a wide variety of substrates. Tilemaster Eco-3000 has been specially developed to provide excellent adhesion properties, with a high bond strength and a hard set once cured.

Tilemaster Eco-3000 is a high temperature adhesive, making it ideal for use onto substrates that have underfloor heating installed; it is also suitable for installations that may be subject to direct sunlight such as orangeries, conservatories and any other glass-fronted buildings.

Formulated to give a fast tacking off time, Tilemaster Eco-3000 can be installed into whilst still wet, or can be allowed to tack off completely before installation. It is ready to accept floor coverings in as little as 10 minutes and once installed, can accept light foot traffic after 12 hours.

COVERAGE: 15kg will cover 50m2 – 60m2

PACK SIZE: 15Kg tub


  • High Temperature – Ideal For Use
  • Above Underfloor Heating Systems
  • Suitable For Installing PVC, Luxury Vinyl Tile, Carpet & Textile and Sheet Vinyl
  • Apply Floorcoverings In As Little As 10 Minutes
  • High Bond Strength & Hard Set



  • Sand/Cement Screed
  • Concrete
  • Plywood Overlay
  • Electric Underfloor Heating
  • Water/Wet System Underfloor Heating
  • Tile Backer Boards
  • Anhydrite Screeds
  • T&G Floorboards
  • Floating Floors



  • LVT
  • PVC Flooring
  • Carpet & Textiles
  • Sheet Vinyl
  • Rubber Flooring
  • Vinyl
  • Uncoupling Membrane




Before starting, all substrates must be clean, dry and strong enough to support the weight of the floor covering and adhesive. Remove all dust, dirt, oil, grease and any other contaminants that may affect adhesion.


On a flat, even substrate where dry conditions exist, trowel out the adhesive with a suitable notched flooring trowel held at approximately 60° and apply the adhesive evenly across the substrate.

When installing into wet adhesive, allow 10 minutes for Tilemaster Eco-3000 to semi-tack off before applying the floor covering onto the adhesive. If allowing the adhesive to fully tack off, leave the adhesive to become touch dry whilst maintaining a tacky feel before applying the floor covering.

Install the floor covering in such a way that air is not caught beneath the floor covering and smooth over from the centre outwards. Using a suitable roller, roll the floor covering evenly and consistently to ensure full contact is made between the adhesive and the floor covering and that any trowel marks from beneath are smoothed over and do not remain.

If applying Tilemaster Eco-3000 to particularly absorbent substrates, applying a thin layer of adhesive onto the substrate prior to application will help aid adhesion and prevent adhesive shadowing or ‘grinning’ through the floor covering.

Ensure that the floor covering manufacturer’s guidelines and laying instructions are followed and adhered to wherever relevant.
Clean surplus adhesive from the face of the floor covering as soon as possible with clean water, as cured adhesive will prove very difficult to remove later.


Allow the adhesive to fully cure before applying loads to the surface. This time is usually 24 hours after completion of installation. Welding of floor coverings must also be done once the adhesive has fully cured, again, approximately 24 hours after installation.
If you are unsure with any of our instructions please call the Tilemaster Technical Helpline on 01772 456831.




COVERAGE: 20kg will cover 5 – 6m² at 3mm thin bed application